Please check our Developer Hub for the following integration guides:
Why are my IPSec tunnels down though the configuration was correct and was not changed?
If no traffic is sent through the IPSec , the tunnels may go down. They will go up as soon as traffic coming from the customer's application server comes through. AWS documentation states: "The VPN tunnel comes up when traffic is generated from your side of the VPN connection. The AWS endpoint is not the initiator; your customer gateway device must initiate the tunnels. "
To keep the tunnel up we advise the customer side to actively try to re-establish the IPsec tunnel (e.g. by means of cron job or by setting up a ping from the application server to an EMnify endpoint). This is because the IPsec SA is eventually removed completely if it fails all the attempts to be re-established (e.g. as result to AWS network outage.
If you're experiencing idle timeouts due to low traffic on a VPN tunnel:
- Be sure that there's constant bidirectional traffic between your application server and our CloudConnect. If necessary, create a host that sends ICMP requests to an instance in your VPC every 5 seconds.
- Review your VPN device's idle timeout settings using information from your device's vendor. When there's no traffic through a VPN tunnel for the duration of your vendor-specific VPN idle time, the IPsec session terminates. Be sure to follow vendor-specific configuration guidelines.
To re-establish a VPN tunnel in case of a network outage (that would typically exceed the DPD timeout interval) we recommend customers to provide an additional mechanism, based on a cron job or by setting up a ping from the application server to an EMnify endpoint. This is because the IPsec SA is eventually removed completely if all the attempts to be re-established fail.e. AWS does not initiate IPsec connections. It only operates in passive mode.
The traffic sent from my Connected Devices does not arrive to my server
- Check where your endpoints are sending the traffic to. If you are using a hostname to address your application servers make sure it resolves to a private IP reachable through CloudConnect.
- Make sure you are allow traffic coming from your endpoint IP addresses:
- If you can, allow traffic from the following ranges
You will then be sure that traffic from your endpoints will be allowed
- If you have overlapping rules, you can allow only the IP ranges assigned to your account. In this case, you need to update your configuration each time a new IP range is assigned to your account.
- If you can, allow traffic from the following ranges
I am getting an error message: "CIDR not valid. X.X.X.X is not available"
You can add up to 3 CIDR in your VPC. If the CIDR is already taken on our side, a warning will be displayed when you try to validate the TGW because AWS TGW does not support overlapping IP addresses. Please use a different CIDR.
I want to update my CloudConnect. How should I proceed?
There is no way to update the configuration of your CloudConnect yet. To do so, delete the attachment and create it again from scratch.
For Transit Gateways, make sure you delete it from the EMnify User Interface. If the attachment is deleted from AWS first, we won't be notified and the configured CIDR will not be available again automatically.
Note: when the old attachment is deleted and then a new one is created, you will be billed for both attachments in the current month.
Note #2: if you delete the attachment from the AWS side only, you will still be charged by EMnify. Please make sure to delete the attachment on the EMnify portal as well.
Can I setup a Transit Gateway / IPSec for a specific subset of IPs?
EMnify's Cloud Connect will enable you to access all your devices. However, you can create rules on your side to enable the access to specific IP addresses only.
What are the differences between OpenVPN and IPSec
EMnify offers different types of VPN:
- The OpenVPN should be used to remotely access devices using EMnify SIM cards from any computer. Please check our OpenVPN FAQ
- IPSec can be used to create a direct connection between an application server and devices connected to the Internet using EMnify SIM cards. With an IPSec, all traffic to and from the devices to and from the application server will go through the tunnel, be encrypted and secured without using the public Internet. It enables the devices to directly access the application within the same network. With the CloudConnect Feature, EMnify offers quick IPSec configuration. For AWS users, they can use the Transit Gateway feature and keep all traffic within AWS:
How IPSec works
IPSec involves many component technologies and encryption methods. Yet IPSec's operation can be broken down into five main steps:
"Interesting traffic" initiates the IPSec process. Traffic is deemed interesting when the IPSec security policy configured in the IPSec peers starts the IKE process.
IKE phase 1. IKE authenticates IPSec peers and negotiates IKE SAs during this phase, setting up a secure channel for negotiating IPSec SAs in phase 2.
IKE phase 2. IKE negotiates IPSec SA parameters and sets up matching IPSec SAs in the peers.
Data transfer. Data is transferred between IPSec peers based on the IPSec parameters and keys stored in the SA database.
IPSec tunnel termination. IPSec SAs terminate through deletion or by timing out.
1. Defining Interesting Traffic
What type of traffic is deemed interesting is determined as part of formulating a security policy for use of a VPN. The policy is then implemented in the configuration interface for each particular IPSec peer. When interesting traffic is generated or transits the IPSec client, the client initiates the next step in the process, negotiating an IKE phase 1 exchange.
2. IKE Phase 1
The basic purpose of IKE phase 1 is to authenticate the IPSec peers and to set up a secure channel between the peers to enable IKE exchanges. IKE phase 1 performs the following functions:
Authenticates and protects the identities of the IPSec peers
Negotiates a matching IKE SA policy between peers to protect the IKE exchange
Performs an authenticated Diffie-Hellman exchange with the end result of having matching shared secret keys
Sets up a secure tunnel to negotiate IKE phase 2 parameters
IKE phase 1 occurs in two modes: main mode and aggressive mode.
Main mode has three two-way exchanges between the initiator and the receiver.
First exchange: The algorithms and hashes used to secure the IKE communications are agreed upon in matching IKE SAs in each peer.
Second exchange: Uses a Diffie-Hellman exchange to generate shared secret keying material used to generate shared secret keys and to pass nonces—random numbers sent to the other party and then signed and returned to prove their identity.
Third exchange: Verifies the other side's identity. The identity value is the IPSec peer's IP address in encrypted form. The main outcome of main mode is matching IKE SAs between peers to provide a protected pipe for subsequent protected ISAKMP exchanges between the IKE peers. The IKE SA specifies values for the IKE exchange: the authentication method used, the encryption and hash algorithms, the Diffie-Hellman group used, the lifetime of the IKE SA in seconds or kilobytes, and the shared secret key values for the encryption algorithms. The IKE SA in each peer is bi-directional.
In aggressive mode, fewer exchanges are made, and with fewer packets. On the first exchange, almost everything is squeezed into the proposed IKE SA values: the Diffie-Hellman public key; a nonce that the other party signs; and an identity packet, which can be used to verify identity via a third party. The receiver sends everything back that is needed to complete the exchange. The only thing left is for the initiator to confirm the exchange. The weakness of using the aggressive mode is that both sides have exchanged information before there's a secure channel. Therefore, it's possible to "sniff" the wire and discover who formed the new SA. However, it is faster than main mode.
3. IKE Phase 2
The purpose of IKE phase 2 is to negotiate IPSec SAs to set up the IPSec tunnel. IKE phase 2 performs the following functions:
Negotiates IPSec SA parameters protected by an existing IKE SA
Establishes IPSec security associations
Periodically renegotiates IPSec SAs to ensure security
Optionally performs an additional Diffie-Hellman exchange
IKE phase 2 has one mode, called quick mode. Quick mode occurs after IKE has established the secure tunnel in phase 1. It negotiates a shared IPSec policy, derives shared secret keying material used for the IPSec security algorithms, and establishes IPSec SAs. Quick mode exchanges nonces that provide replay protection. The nonces are used to generate new shared secret key material and prevent replay attacks from generating bogus SAs.
Quick mode is also used to renegotiate a new IPSec SA when the IPSec SA lifetime expires. Base quick mode is used to refresh the keying material used to create the shared secret key based on the keying material derived from the Diffie-Hellman exchange in phase 1.
Perfect Forward Secrecy
If perfect forward secrecy (PFS) is specified in the IPSec policy, a new Diffie-Hellman exchange is performed with each quick mode, providing keying material that has greater entropy (key material life) and thereby greater resistance to cryptographic attacks. Each Diffie-Hellman exchange requires large exponentiations, thereby increasing CPU use and exacting a performance cost.
4. IPSec Encrypted Tunnel
After IKE phase 2 is complete and quick mode has established IPSec SAs, information is exchanged via an IPSec tunnel. Packets are encrypted and decrypted using the encryption specified in the IPSec SA.
5. Tunnel Termination
IPSec SAs terminate through deletion or by timing out. An SA can time out when a specified number of seconds have elapsed or when a specified number of bytes have passed through the tunnel. When the SAs terminate, the keys are also discarded. When subsequent IPSec SAs are needed for a flow, IKE performs a new phase 2 and, if necessary, a new phase 1 negotiation. A successful negotiation results in new SAs and new keys. New SAs can be established before the existing SAs expire, so that a given flow can continue uninterrupted.
Here is the list of AWS supported algorithms which are available:
IKEv1 and IKEv2
- VPN on demand, meaning if there is no actual traffic within the tunnel, it will go down. So, there should be a constant traffic being initiated on the tunnel.
- There is no way to initiate the tunnel on the EMnify side, which means the customer needs to restart the IPsec to reestablish the tunnel.
- The tunnel will stays up and running even there is no actual data traffic monitored within the tunnel.
- IPsec can be reestablished once tunnel goes down and encountered interruptions by enabling parameters on the customer side:
- DPD timeout action(RESTART)
- Startup action(start)
- These parameters once configured on your side will be accepted automatically by EMnify, since this is already enabled by default and will just accept any configuration negotiated by you.
- We still have the limitation that the negotiation shall be initiated from your side.
- Currently, the parameter change related to DPD timeout action and Startup action cannot be changed from the EMnify side